Boundary Waters Quetico Forum :: Gear Forum :: So I made a Reflector oven today...
|
Author | Message Text | ||
whiteh20 |
Nice post, Good winter project!! |
||
kanoes |
|
||
snakecharmer |
|
||
mwd1976 |
In researching the jello mold oven on this site, someone mentioned a stove top potato baker. Looks like it's similar in concept to what you came up with. potato baker I would imagine you could bake about anythng in it as long as it was small enough. for $15 it might be worth a try. |
||
lostreef |
reflector oven plans |
||
snowman |
|
||
mwd1976 |
Have you ever done the "bakepacker" style baking? Where you essentially steam bake something in a ziploc bag? I've made muffins that way, I just haven't played around with it much. I put about a half inch of water in my larger pot, put a smaller pot lid inside it spaced up on some rocks, and muffin batter in a ziploc. Cover the large pot and start boiling. I think it took about 20 minutes to make my muffin glob:) Or you can use the real deal... http://www.bakepacker.com/ |
||
Grandma L |
|
||
Savage Voyageur |
|
||
mwd1976 |
First I drew up some super detailed and technical plans for my creation: I used a high tech new CAD program for this :) Note the complete lack of dimensions. You may want to add this option to your drawings. I then headed to Home Depot and picked up a 3'x3' piece of light gauge aluminum (or as the English say: al-you-minny-um) a few small brass hinges, some rivets, and a little hand bender thingy. The hand bender thingy was near the gutters and flashing. I'm pretty sure that's its proper name. Now it was time to start putting those expensive drawings to use. First I laid out the sides. I added 3/4" to what I decided my finished dimension should be. I would have consulted my drawings here, but the lack of dimensions limited their usefulness. I did this to accomodate the 3/8" hem I would bend around the edges to add strength and also hide any sharp edges. don't forget to file all the edges down. This stuff is sharp! Next I clipped the corners to allow the hem to fold over on itself. I then proceeded to use the hand-bender-thingy to bend a 3/8" hem I hammered it flat using a block and a hammer (also known as a hand hitting thingy) after repeating a few times I had both sides done. I would later cut this down a bit because it was too deep. Turns out dimensions on a drawing are a good idea. Who knew? I came up with the idea to use some "Z" clips to hold all the parts together. To make these I first cut a strip about 1.25" wide by 6" or so long. I then hemmed the edge over like I've already shown. I inserted the hem into the bender thingy and hammered the remainder of the strip down using a block. The result was a fancy handmade Z clip Pretty slick huh? Is genius too strong a word? Ok...Yeah it probably is:) Now I cut these into about 1.25" lengths and riveted them to the sides, the tops of the clips even to the lines I had drawn where I wanted the top, baking shelf, and lower reflector to sit. Now it was time to make the shelf and the bottom. I made these the same size so they'd be interchangeable. Because I am using pretty light gauge stuff, I had to add some strength to these. I added 1.5" to my finished dimenision to account for the hem and plus a 90 degree bend. Leaving this 90 degree bend adds significant stregth the the pieces. Once I did that on all four sides of both pieces I had my shelf and bottom reflector. Now on to the top. It was essentially more of the same, but I added a hinged back panel so I could control temperature and also access the baked goods. This way I could rotate them and burn them to a crisp evenly. The 90 degree bends on the shelf, bottom, and top slide into my fancy "Z" clips (patent pending :) that are riveted onto the sides. Ths is what holds the whole works together. It seems stable enough. I can set it up in about 20 seconds, and it breaks down pretty flat. I set out to build something that required no tools or hardware to assemble, and I think I did ok. Will it work? I have no idea. I have never used one, nor seen one in person. I guess I'll have to wait a couple months before I can try it out. I hope my techincal jargon wasn't over any of your heads:) All told I spent about $40 or so on this project including the hand bender thingy, rivets,and hinges. This was meant to share some ideas and possibly inspire some of you to try your own as well. Hopefully you'll see something that can be improved upon. Any and all comments are welcome. Cheers. |
||
Beavers |
Looks like it packs down pretty small. I've always been interested in building a reflector oven, just never got around to it. I think you might of motivated me to give it a try! BTW- I'm running the same CAD program you have, but mine is only version 3.0 :( |
||
Soledad |
|
||
mwd1976 |
|
||
izzy |
|
||
dogwoodgirl |
|
||
wetcanoedog |
WOW!!!--super high quality work--looks like a pro job..no wavey or out of line parts..nifty Z clips..the back door is a good idea that i have not seen on the plans in the older outdoor books.. that has Pineapple upside down cake written all over it..i bought a reflector last summer and spent more than a few $$$ for it..that looks just as good--we will be looking forward to the photos with the results of you cooking adventures-- |
||
mwd1976 |
I'm glad I didn't lose ya Dogwoodgirl;) Duckcall, I don't know about the slots. Most of the ones I've seen pictures of don't have them, so I wouldn't think so. Maybe someone who has actually used one can chime in. Hey Beavers, is your CAD version 3.0 the one where you use a pointy stick in the sand? :) |
||
duckcall |
|
||
quetico152 |
I worked for a HVAC company for a couple years, and i dont know the real name for youre "hand bender thingy", but what we always called them were "hand breaks." surprisingly thats even shorter than youre made up name. |
||
mwd1976 |
I think it's called a hand former, I believe a hand brake is actually the big flat pliers type of tool. The names are probably pretty interchangable though. I was mostly in just a goofy mood when I wrote it and tried to keep things light and from getting too boring. In retrospect, I should have put the real name on here, the folks at Home Depot might look at you a bit funny if you asked where they kept the "Hand bender thingys" :) |
||
dogwoodgirl |
|
||
mwd1976 |
Looks like a fairly simple plan, I'd maybe still hem those edges for some strength. |
||
Grandma L |
|
||
moose plums |
|
||
quetico152 |
I worked for my dad too, and i used to make goofy stuff all the time as a kid, just the same as you. And im pretty sure all HVAC places have different terminology for everything, cause we called the big flat pliers "duck billed pliers". and dont ask me why, cause i dont know. |
||
aebrooks |
Reflector oven plans |
||
Grandma L |
|
||
kanoes |
|